Analysis of Band Curvature in Asymmetrical Rolling Process by FEM Method

Publish Year: 1395
نوع سند: مقاله کنفرانسی
زبان: English
View: 396

This Paper With 7 Page And PDF Format Ready To Download

  • Certificate
  • من نویسنده این مقاله هستم

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این Paper:

شناسه ملی سند علمی:

NSMI18_258

تاریخ نمایه سازی: 6 اسفند 1395

Abstract:

Today, the rolled products, i.e. sheet, plate and foil is used in marine applications, including platforms, hatch covers, mast, hulls of boats and superstructures on pleasure boats and the bridges and superstructures of passenger ships and merchant ships. In this paper, simulation of asymmetric cold rolling is presented by using explicit analysis procedure. In asymmetric cold rolling, the workpiese if often bent downwards or upwards. A two dimensional explicit dynamic finite element model with adaptive meshing technique has been employed to simulate asymmetrical condition are here due to different roll radii. To validate the simulation, the results of simulation and experiment are compared. Effects of asymmetry due to roll radii ratio and speed ratio mismatch on sheet curvature variations are discussed. Finally, optimum roll speed ratio in various of roll radii ratio could be found to produce flat sheet.

Authors

Hassan Sayyaadi

Ph.D, Sharif University of Technology/ Department of Mechanical Engineering

Ramin Yekta

M.SC Student, Sharif University of Technology/ Department of Mechanical Engineering;

Abolfazl Motekallem

M.SC Student, Sharif University of Technology/ Department of Mechanical Engineering

مراجع و منابع این Paper:

لیست زیر مراجع و منابع استفاده شده در این Paper را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود Paper لینک شده اند :
  • G. Sachs, L.J. Klingler, The flow of metals through tools ...
  • L. Holbrook, C.F. Zorowski, Effects of non symmetry in strip ...
  • G.E. Kennedy, F. Slamar, Turn up and turm dow in ...
  • S.A. Buxton, S.C. Browning, Turn up and turndown in hot ...
  • W. Johnson, G. Needham, an experimental study of asymmetrical rolling, ...
  • W. Johnson, G. Needham, Further experiments in asymmetrical rolling, Int. ...
  • P. Dewhurst, I.F. Collins, W. Johnson, A theoretical and experimental ...
  • M.M. Kiuchi, S. Hsiang, Analytical model of asymmetrical rolling process ...
  • J. Pospiech, a note on the influence of some factos ...
  • A.B. Richelsen, Elastic-plastic analysis of the stress and strain distributions ...
  • R. Shivpuri, P.C. Chou, C.W. Lau, Finite element investigation of ...
  • L.-S. Lu, O.-K. Harrer, W. Schwenzfeier, F.D. Fischer, Analysis of ...
  • Y.M. Hwang, T.H. Chen, Analysis of asymmetrical rolling by stream ...
  • M. Salimi, F. Sassani, Modified slab analysis of asymmetrical plate ...
  • M. Pietrzyk, K. Wilk, H. Kusiak, Steady state FEM simulation ...
  • S. Hamuzu, K. Yamada, T. Kawanmi, et al., Rigid plastic ...
  • Y.M. Hwang, G.Y. Tzou, Analytical and experimental study on asymmetric ...
  • H.DD. Hibbitt, B.I. Karlson, D. Sorensen, HKS Inc. Rolling of ...
  • M. Salimi, A. Forghani, Prediction of product curvature in rolling ...
  • نمایش کامل مراجع