Simulation of a New Process Design to Fabricate a Rectangular Twist Waveguide Using Extrusion and a Twist Die

Publish Year: 1398
نوع سند: مقاله ژورنالی
زبان: English
View: 283

This Paper With 10 Page And PDF Format Ready To Download

  • Certificate
  • من نویسنده این مقاله هستم

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این Paper:

شناسه ملی سند علمی:

JR_IJMF-6-2_006

تاریخ نمایه سازی: 9 اسفند 1399

Abstract:

The aim of the present study is to determine the feasibility of making a rectangular twist waveguide used to rotate electromagnetic waves. For this purpose, the process of fabricating an aluminum rectangular twist waveguide was simulated by making use of finite element method and Deform software. The optimum length and angle of the twist die for manufacturing a twist waveguide with inner cross sectional dimensions of 22.86 mm × 10.16 mm and a length of 50 mm and twisting angle of 90 degrees were investigated. Moreover, the effect of certain factors such as the length, thickness, cross section dimensions of the waveguide and friction on the optimum length of the twist die and cross sectional distortion was studied. The results of this study indicated that the length of the twist die had an influence on the amount of twisting, while friction was of no importance. In addition, comparing the values of effective stress and flow stress at the cross section of the workpiece behind the twist die depicted that the workpiece would not yield behind the twist die due to smaller values of effective stress.

Keywords:

Extrusion , Rectangular twist waveguide Simulation , Twist die

Authors

Mina Amiri

Department of Materials Science and Engineering, School of Engineering, Shiraz University, Shiraz, Iran

Ramin Ebrahimi

Department of Materials Science and Engineering, School of Engineering, Shiraz University, Iran.

مراجع و منابع این Paper:

لیست زیر مراجع و منابع استفاده شده در این Paper را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود Paper لینک شده اند :
  • [1] U. A. Bakshi, A. V. Bakshi, Transmission Lines and ...
  • [2] V. S. Bagad, Microwaves and Radar, Technical Publications, Pune ...
  • [3] M. Sharififar, S. A. A. Akbari Mousavi, Simulation and ...
  • [4] A. S. Khan, Microwave Engineering: Concepts and Fundamentals, CRC ...
  • [5] G. E. Dieter, D. J. Bacon, Mechanical Metallurgy, McGraw-Hill, ...
  • [6] M. M. Moshksar, R. Ebrahimi, An analytical approach for ...
  • [7] S. H. Kim, S. W. Chung, S. Padmanaban, Investigation ...
  • [8] N. R. Chitkara, A. Aleem, Axi-symmetric tube extrusion/piercing using ...
  • [9] S. Hansson, Simulation of Stainless Steel Tube Extrusion, Doctoral ...
  • [10] L. De Pari, W. Z. Misiolek, Numerical modeling of ...
  • [11] J. Lof, Y. Blokhuis, FEM simulations of the extrusion ...
  • [12] J. M. Lee, B. M. Kim, C. G. Kang, ...
  • [13] H. H. Jo, S. K. Lee, C. S. Jung, ...
  • [14] W. Xianghong, Z. Guoqun, L. Yiguo, M. Xinwu, Numerical ...
  • [15] G. Liu, J. Zhou, J. Duszczyk, FE analysis of ...
  • [16] L. Li, H. Zhang, J. Zhou, J. Duszczyk, G. ...
  • [17] C. Zhang, G. Zhao, Z. Chen, H. Chen, F. ...
  • [18] C. Zhang, G. Zhao, H. Chen, Y. Guan, F. ...
  • [19] D. Y. Yang, T. Altan, Analytical and experimental investigation ...
  • [20] D. Y. Yang, K. Lange, Investigation into non-steady-state three-dimensional ...
  • [21] Y. B. Park, J. H. Yoon, D. Y. Yang, ...
  • [22] H. Yoshida, Y. Sawaki, Y. Sakaida, Shaping of helical ...
  • [23] N. B. Khalifa, A. E. Tekkaya, Newest developments on ...
  •  [24] Y. M. Hwang, C. N. Chang, Hot extrusion of ...
  • [25] Military Standardization Handbook, Fabrication of Rigid Waveguide Assemblies (Sweep ...
  • [26] N. Pardis, R. Ebrahimi, Deformation behavior in Simple Shear ...
  • [27] P. Eskelinen, Introduction to RF Equipment and System Design, ...
  • نمایش کامل مراجع