Effect of Volume Fraction on Nanoindentation of Nanocomposite using FEM

Publish Year: 1387
نوع سند: مقاله کنفرانسی
زبان: English
View: 1,142

متن کامل این Paper منتشر نشده است و فقط به صورت چکیده یا چکیده مبسوط در پایگاه موجود می باشد.
توضیح: معمولا کلیه مقالاتی که کمتر از ۵ صفحه باشند در پایگاه سیویلیکا اصل Paper (فول تکست) محسوب نمی شوند و فقط کاربران عضو بدون کسر اعتبار می توانند فایل آنها را دریافت نمایند.

  • Certificate
  • من نویسنده این مقاله هستم

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این Paper:

شناسه ملی سند علمی:

ICNN02_257

تاریخ نمایه سازی: 27 شهریور 1391

Abstract:

The purpose of the present work is to investigate the nanoindentation process of exfoliated nylon 66 /clay nanocomposite by numerical simulation. First the tensile test on a two dimensional representative volume element (RVE) is simulated and stress-strain curve is obtained. Then by using this stress-strain curve, the nanoindentation process of nanocomposite is simulated as an isotropic material. Finally, the effect of indenter angle is investigated. The simulation results for load-displacement curve show that there is a good agreement between the numerical and experimental results. Furthermore, it is observed that the simulation results of nanoindentation depend greatly on the mesh size but very little on the friction coefficient of indenter and specimen.Since many technologies have moved to ever smaller scale, characterization of the intrinsic mechanical properties of materials has become more difficult and complicated. Polymer/clay nanocomposites are polymeric materials that are reinforced by nanoclay particles whose dimensions are in the sub-micron scale and the particles are composed of stacks of 1 nm thick mono-layers whose in-plane dimensions range from 100 nm to 1000 nm. Nanoindentation testing at very low load is a successful technique for studying the mechanical properties of these materials.Finite element method (FEM) has been widely used for numerical simulation of hardness tests on bulk material in order to analyze its deformation response and investigate the influence of indenter geometry, friction and material elastic and plastic properties. In this paper, FEM was used to study the nanoindentation behavior of nylon 66 / clay nanocomposites.

Authors

M Saadatfar

Faculty of Mechanical Engineering, University of Tehran, Tehran, Iran

مراجع و منابع این Paper:

لیست زیر مراجع و منابع استفاده شده در این Paper را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود Paper لینک شده اند :
  • Shen L, Phang IY, Chen L, Liu TX, Zeng KY, ...
  • Ray S. Fertig III Mark R. Garnich, Composites science and ...
  • K. Hbaieb, Q.X. Wang, Y.H.J. Chia, B. Cotterell, Polymer, 48, ...
  • نمایش کامل مراجع