An Investigation on Mold Powders Properties Consumed in Iran

Publish Year: 1386
نوع سند: مقاله ژورنالی
زبان: English
View: 67

This Paper With 5 Page And PDF Format Ready To Download

  • Certificate
  • من نویسنده این مقاله هستم

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این Paper:

شناسه ملی سند علمی:

JR_ISSIRAN-4-1_008

تاریخ نمایه سازی: 6 آبان 1402

Abstract:

This paper describes the work done between IUST and two Iranian steelworks to evaluate and review the performance of mould fluxes in current use for continuous casting. Calculations have been performed to compare actual values of powder consumption, viscosity and break temperature of the fluxes in current use with required values derived from published empirical rules for casting conditions. It has been found that there is, in general, poor agreement between actual and required values. The required viscosities of mould fluxes consumed in MC grades are ۲.۲ and ۱.۹ dPas while the measured values are ۱.۵ and ۱.۱ dPas, respectively indicating higher values. This situation is reverse in LC grades, and actual viscosities are lower than the measured values based on empirical rules. There is also a disagreement between the carbon content and break temperature of the current fluxes and required values resulting in the defects in produced slabs. These differences are more critical in MC grades. This does not necessarily mean that fluxes are not working well but does imply that a review of mould flux performance is needed before the planned increases in production are implemented. One steel company experienced problems with overflows of steel (bleeds) and with depressions in the surface of the slab. Possible reasons for the formation of these defects are proposed.

Authors

A. Azhari

Department of Materials Engineering, Iranian University of Science and Technology (IUST), Tehran, Iran

F. Golestani-Fard

Department of Materials Engineering, Iranian University of Science and Technology (IUST), Tehran, Iran

KC. Mills

Department of Materials, Imperial College, London, UK

F. Pourdavoud

Technical Department, Pishgam Company

M. Rasti

Research and Development, Khouzestan Steel Company, Ahwaz, Iran

J. Izadi

Research and Development, Mobarakeh Steel Company, Isfahan, Iran

مراجع و منابع این Paper:

لیست زیر مراجع و منابع استفاده شده در این Paper را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود Paper لینک شده اند :
  • M. Wolf AIME Elec. Furnace Proc. ۴۰(۱۹۸۲), ۳۳۵ ...
  • S. Ogibayashi,NipponSteel Technical Rept. ۳۴(۱۹۸۷), ۱/۱۰ ...
  • M. Wolf, Proc. ۲nd Europ. Conf. Continuous casting heldDusseldorf, (۱۹۹۴), ...
  • S. Sridhar and K. C. Mills, Proc. Brimacombe Symposium heldVancouver, ...
  • A. B. Fox, Ph.D Thesis,ImperialCollege,London, (۲۰۰۴) ...
  • R. Saraswat, A. B. Fox, K. C. Mills, P. D. ...
  • K. C. Mills and A.B. Fox, ISIJ Intl. ۴۳(۲۰۰۳), ۱۴۷۹/۱۴۸۶ ...
  • M. Jenkins Proc. ۷۸th Steelmaking Conf. (۱۹۹۵), ۳۳۷ ...
  • M. S. Jenkins and B. G. Thomas Proc. ۷۹th Steelmaking ...
  • J. W. Kim, Proc. ۷۸ th Steelmaking Conf., (۱۹۹۵), ۳۳۳ ...
  • نمایش کامل مراجع