The Influence of the Nickel Content on Microstructure and Mechanical Properties of the Al-Mg Weld Metal

Publish Year: 1396
نوع سند: مقاله ژورنالی
زبان: English
View: 302

متن کامل این Paper منتشر نشده است و فقط به صورت چکیده یا چکیده مبسوط در پایگاه موجود می باشد.
توضیح: معمولا کلیه مقالاتی که کمتر از ۵ صفحه باشند در پایگاه سیویلیکا اصل Paper (فول تکست) محسوب نمی شوند و فقط کاربران عضو بدون کسر اعتبار می توانند فایل آنها را دریافت نمایند.

  • Certificate
  • من نویسنده این مقاله هستم

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این Paper:

شناسه ملی سند علمی:

JR_JEFM-1-2_006

تاریخ نمایه سازی: 25 تیر 1398

Abstract:

In this investigation, the microstructure and mechanical properties of the Al 5058 weld metals have been studied in respect of Nickel content in the range of 0.5 to 4.5 percent. Samples were produced by automatic TIG welding process in Butt weld condition with different wire feeder speed rate of pure nickel filler metal. The optical metallography and EDX analysis result shows that by increasing of the nickel content in the weld metal, the grain size decreased and the volume fraction of the          inter-metallic compounds of Nickel rich phase was increased. The mechanical test results show that by increasing of the nickel content in the weld metal, the tensile and yield strength increased, whilst impact energy and elongation decreased.

Authors

F. Sharifi

Iranian Institute of Welding and Nondestructive Testing (IWNT), Tehran, Iran.

مراجع و منابع این Paper:

لیست زیر مراجع و منابع استفاده شده در این Paper را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود Paper لینک شده اند :
  • J. Norrish: Advanced welding processes, Woodhead publishing limited, Cambridge, England, ...
  • R. J. Davis: ASM Specialty Hand book, Aluminum and aluminum ...
  • C. E. Cross, D. L. Olson and S. Liu: Aluminum ...
  • S. Honma, K. Yasuda, Weld. Int., 18(2004), 450. ...
  • P. B. Dickerson, B. Irving, Weld. J., 72(1992), 45. ...
  • G. Mathers: The welding of aluminum and it’s alloys, Wood ...
  • H. Okamato: Alloys phase diagrams, ASM International, USA, (2002). ...
  • K. Esterling: Introduction to physical metallurgy of welding, second edition, ...
  • S. A. David, J. M. Vitek, Int. Met. Rev., 8(1989), ...
  • H. Sabet, The International Institute of Welding Congress, IIWC, Iran, ...
  • H. Sabet, Welding of Nonferrous Metals, IWNT Publication, Tehran, (2014). ...
  • نمایش کامل مراجع