Sliding wear behaviour of walnut shell powder filled vinyl Ester/ WSP green composites

Publish Year: 1395
نوع سند: مقاله ژورنالی
زبان: English
View: 291

This Paper With 9 Page And PDF Format Ready To Download

  • Certificate
  • من نویسنده این مقاله هستم

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این Paper:

شناسه ملی سند علمی:

JR_ICC-5-2_003

تاریخ نمایه سازی: 2 مهر 1398

Abstract:

Polyvinyl ester green composites were synthesized with walnut shell powder (WSP) by in-situ polymerization technique. The green composites have been evaluated for mechanical properties such as tensile strength, tensile modulus and hardness. Sliding wear loss, specific wear rate and coefficient of friction were investigated by using computerized pin-on–disc machine at normal applied loads of 20, 30 and 40N; at a sliding velocity of 1.5 m/s and at two abrading distances viz., 100 and 200 m. The results indicate that the wear volume loss increases with increasing abrading distance/load. It was found that WSP filled vinyl ester composites exhibit lower wear rate and higher coefficient of friction as compared to vinyl ester green composites. Further, the worn surfaces were examined by scanning electron microscopy (SEM), to give insight in to the wear mechanism, while their mechanical properties were investigated using tensile strength, tensile modulus and hardness test machines.

Authors

Shahryar Pashaei

payame noor university

Soleyman Hosseinzadeh

Department of Chemistry, Payame Noor University, P.O. BOX ۱۹۳۹۵-۳۶۹۷ Tehran, Iran

مراجع و منابع این Paper:

لیست زیر مراجع و منابع استفاده شده در این Paper را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود Paper لینک شده اند :
  • E. Bozkurt, E. Kaya, M. Tanoglu, Comp Sci Tech., 2007, ...
  • M.W. Nielsen, J.W. Schmidt, J.H. Hogh, J.P. Waldbjorn, J.H. Hattel, ...
  • W. Hufenbach, K. Kunze, J. Bijwe, J Synth Lub, 2013, ...
  • M.N. Islam, M.R. Rahman, M.M. Haque, M.M. Huque, Comp Part ...
  • M. Krzesinska, J. Zachariasz, A.I. Lachowski, Bio Tech, 2009, 100, ...
  • A. Arbelaiz, B. Fernandez, A. Valea, I. Mondragon, Carbo Polym, ...
  • M. Assarar, D. Scida , A.El Mahi , C. Poilâne ...
  • Y. Mohd Yuhazri, P.T. Phongsakorn, H. Sihambing, Int J Bas ...
  • S. Pashaei, B. Siddaramaiah, A.A. Syed, Polym-Plast Tech Eng, 2011, ...
  • B.D. Agarwal, L.J. Broutman, John Wiley and Sons, New York, ...
  • J.P. Dhal, S.C. Mishra, Journal of Materials, 2013, 32, 1-6. ...
  • B. Gangil, A. Patnaik, A. Kumar, M. Kumar, J Mat ...
  • A.A.Yussuf, I. Massoumi, A. Hassan, J Polym the Env, 2010, ...
  • K. Salasinska, J. Ryszkowska, Comp Inter, 2012, 19(5), 321-332. ...
  • H. Pıhtılı, N. Tosun, Wear, 2002, 252, 979–984. ...
  • G. Agarwal, A. Patnaik, R.K. Sharma, AdvComp, 2014, 23, 293-317. ...
  • M.B.J. LOW, Wear, 1979, 52, 347– 363. ...
  • Gaura Agarwal, Amar Patnaik, Rajesh Kumar, Int J Eng Res ...
  • M.A. Chowdhury, M.M. Helali, Trib Int, 2009, 42, 946-950. ...
  • B.Bhushan, A.V. Kulkarni, Thin Sol Fil, 1996, 278, 49-56. ...
  • نمایش کامل مراجع