Accuracy Improvement of Upper Bound Analysis of Bimetallic Rods Extrusion Using a New Velocity Field

Publish Year: 1395
نوع سند: مقاله ژورنالی
زبان: English
View: 185

This Paper With 9 Page And PDF Format Ready To Download

  • Certificate
  • من نویسنده این مقاله هستم

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این Paper:

شناسه ملی سند علمی:

JR_ADMTL-9-4_011

تاریخ نمایه سازی: 18 اردیبهشت 1400

Abstract:

In this paper, the direct extrusion process of bimetallic rods in conical dies is analyzed by an improved upper bound method. The deformation zone is subdivided into six smaller zones and by considering a non-spherical entrance boundary to the deformation zone, a velocity field is presented which is different from velocity fields employed in previous studies. The total power consumption of the process including internal, shear and frictional powers is obtained using this velocity field, and then the forming force is calculated by employing the upper bound theory. The superior accuracy of the proposed analysis is demonstrated by comparing the computed force with available experimental data and results of an upper bound analysis in the literature. Finally, the developed model is employed to study the effect of some process parameters on the forming load. It is observed that there is an optimal die angle that minimizes the extrusion force. The value of this optimum angle increases with friction coefficient.

Authors

Hamed Afrasiab

Babol University of Technology

Mojtaba Qasemi-Mahallekolaei

Babol University of Technology

مراجع و منابع این Paper:

لیست زیر مراجع و منابع استفاده شده در این Paper را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود Paper لینک شده اند :
  • Ahmed, N., “Extrusion of Copper Clad Aluminum Wire,” J. Mech. ...
  • Berski, S., Dyja, H., Banaszek, G., and Janik, M., “Theoretical ...
  • Osakada, K., Limb, M., and Mellor, P. B., “Hydrostatic Extrusion ...
  • Avitzure, B., Wu, R., Talbert, S., and Chou, Y. T., ...
  • Avitzure, B., Wu, R., Talbert, S., and Chou, Y. T., ...
  • Peng, D. S., “An Upper-Bound Analysis of the Geometric Shape ...
  • Tokuno, H., and Ikeda, K., “Analysis of Deformation in Extrusion ...
  • Chitkara, N. R., Aleem, A., “Extrusion of Axi-Symmetric Bimetallic Tubes ...
  • Hwang, Y. M., and Hwang, T. F., “An Investigation into ...
  • Haghighat, H., Asgari, G. R., “A generalized Spherical Velocity Field ...
  • Haghighat, H., Amjadian, P., “A Generalized Upper Bound Solution for ...
  • Haghighat, H., Mahdavi, M., “Upper Bound Analysis of Bimetallic Rod ...
  • Haghighat, H., Mahdavi, M. M., “Analysis and FEM Simulation of ...
  • Haghighat, H., Shayesteh, H., “Upper Bound Analysis for Hybrid Sheet ...
  • Prager, W., Hodge, P. G., “Theory of Perfectly Plastic Solids”, ...
  • Unckel, H. A., “Extrusion - Some Experimental Work on Hot ...
  • Kalpakjian, S., “Manufacturing Processes for Engineering Materials”, 5th ed., Addison-Wesley, ...
  • نمایش کامل مراجع