Influence of Addendum Modification Factor on Root Stresses in Normal Contact Ratio Asymmetric Spur Gears

Publish Year: 1398
نوع سند: مقاله ژورنالی
زبان: English
View: 223

This Paper With 12 Page And PDF Format Ready To Download

  • Certificate
  • من نویسنده این مقاله هستم

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این Paper:

شناسه ملی سند علمی:

JR_JSMA-11-1_015

تاریخ نمایه سازی: 12 اسفند 1398

Abstract:

Tooth root crack is considered as one of the crucial causes of failure in the gearing system and it occurs at the tooth root due to an excessive bending stress developed in the root region. The modern power transmission gear drives demand high bending load capacity, increased contact load capacity, low weight, reduced noise and longer life. These subsequent conditions are satisfied by the aid of precisely designed asymmetric tooth profile which turns out to be a suitable alternate for symmetric spur gears in applications like aerospace, automotive, gear pump and wind turbine industries. In all step up and step down gear drives (gear ratio > 1), the pinion (smaller in size) is treated as a vulnerable one than gear (larger in size) which is primarily due to the development of maximum root stress in the pinion tooth. This paper presents an idea to improve the bending load capacity of asymmetric spur gear drive system by achieving the same stresses between the asymmetric pinion and gear fillet regions which can be accomplished by providing an appropriate addendum modification. For this modified addendum the pinion and gear teeth proportion equations have been derived. In addition, the addendum modification factors required for a balanced maximum fillet stress condition has been determined through FEM for different parameters like drive side pressure angle, number of teeth and gear ratio. The bending load capacity of the simulated addendum modified asymmetric spur gear drives were observed to be prevalent (very nearly 7%) to that of uncorrected asymmetric gear drives.

Authors

R Prabhu Sekar

Mechanical Engineering Department, Motilal Nehru National Institute of Technology, Allahabad, India

R Ravivarman

Research Scholar Department of Mechanical Engineering, Pondicherry Engineering college, Pondicherry, India

مراجع و منابع این Paper:

لیست زیر مراجع و منابع استفاده شده در این Paper را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود Paper لینک شده اند :
  • Buckingham E., 1988, Analytical Mechanics of Gears, Dover Publications, Inc. ...
  • Kapelevich A., 2000, Geometry and design of involute spur gears ...
  • Muni D.V., kumar V.S., Muthuveerappan G., 2007, Optimization of asymmetric ...
  • Yang S.C., 2007, Study on internal gear with asymmetric involute ...
  • Muni D.V., Muthuveerappan G., 2009, A comprehensive study on the ...
  • Karat F., Ekwaro-Osire S., Cavdar K., Babalik F.C., 2008, Dynamic ...
  • Costopoulos Th., Spitas V., 2009, Reduction of gear fillet stresses ...
  • Alipiev O., 2011, Geometric design of involute spur gear drives ...
  • Sekar P., Muthuveerappan G., 2014, Load sharing based maximum fillet ...
  • Mohan N.A., Senthilvelan S., 2014, Preliminary bending fatigue performance evaluation ...
  • Marimuthu P., Muthuveerappan G., 2016, Design of asymmetric normal contact ...
  • Marimuthu P., Muthuveerappan G., 2016, Investigation of load carrying capacity ...
  • Thomas B., Sankaranarayanasamy K., Ramachandra S., Kumar S., 2018, Search ...
  • Shuai M., Shuai M., Geoguang J., Jiabai G., 2018, Design ...
  • نمایش کامل مراجع