سیویلیکا را در شبکه های اجتماعی دنبال نمایید.

Wind Tunnel Aerodynamic Coefficients Evaluation of RP Models based on Layer’s Thickness Affect

Publish Year: 1386
Type: Conference paper
Language: English
View: 1,590

This Paper With 8 Page And PDF Format Ready To Download

Export:

Link to this Paper:

Document National Code:

ICME08_043

Index date: 18 November 2009

Wind Tunnel Aerodynamic Coefficients Evaluation of RP Models based on Layer’s Thickness Affect abstract

Nowadays, rapid prototyping (RP) methods are widely used to produce wind tunnel testing models where layer thickness is important parameter that affects aerodynamic characteristics of such wind tunnel models. This paper describes the affects of layer thickness on aerodynamic coefficients for constructed wind tunnel testing of models produced via rapid prototyping technology. Three models were evaluated, where these models were fabricated from ABSi by fused deposition method (FDM). The layer thickness applied, was 0.178mm, 0.254mm and 0.33mm. The surface roughnesses for each model were respectively 25μm, 63μm and 160μm (RZ) that was determined by PERTHOMETER2. A wing-body-tail configuration was chosen for the actual study. Testing covered the Mach range of Mach 0.3 to Mach 1.2 at an angle-of-attack range of -4° to +16° at zero sideslip. Coefficients of normal force, axial force, pitching moment, and lift over drag are shown at each of these mach numbers. Results from this study show that layer thickness does have effect on the aerodynamic characteristics: in general the data differ between the three models by fewer than 6%. The layer thickness does have more effect on the aerodynamic characteristics when mach number is decreased and had most effect on the aerodynamic characteristics of axial force and its derivative coefficients.

Wind Tunnel Aerodynamic Coefficients Evaluation of RP Models based on Layer’s Thickness Affect Keywords:

Wind Tunnel Aerodynamic Coefficients Evaluation of RP Models based on Layer’s Thickness Affect authors

S DANESHMAND

lecturer Mechanical Engineering Department Islamic Azad University Majlessi Beranch, Isfahan, Iran

S RAHMATI

assistant Professor

R ADELNIA

lecturer

مراجع و منابع این Paper:

لیست زیر مراجع و منابع استفاده شده در این Paper را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود Paper لینک شده اند :
Koster, W.P, Field, M. "Effects of Machining Variables on the ...
ladson, C.L., "Effects of Independent Variation of Mach and Reynolds ...
Song, Y., Yan, Y., Zhang, R., Xu, R. and Wang, ...
Onuh, S. O. "Rapid prototyping integrated sys-tems" Rapid Prototyping Journal, ...
COOPER, K. "Rapid Prototyping Technology". New York, Marcel Dekker, 2001. ...
Pandey, P.M., Thrimurthuul lu, K., Reddy, N.V. "Optimal Part Deposition ...
Thrimurthullu, K., Pandey, P.M., Reddy, N.V. "Part Deposition Orientation _ ...
Jones, Pandey, R.T., "The Oblique Wing craft design for Transonic ...
Springer A., Cooper K., "Application of Rapid Prototyping Methods to ...
Springer, A.; Cooper, K.; and Roberts, F. "Application of Rapid ...
Springer A., Cooper K., "Comparing the Aerodynamic C haracteristics of ...
نمایش کامل مراجع